Showing posts with label mercury thermostats. Show all posts
Showing posts with label mercury thermostats. Show all posts

Saturday, August 9, 2014

Honeywell YTHX9321R5061 Prestige® 2.0 HD Comfort System Kit Review

Honeywell YTHX9321R5061 Prestige® 2.0 HD Comfort System Kit
Customer Ratings: 5 stars
Buy Now
I bought this thermostat and installed it myself though Honeywell is quite clear that this is not for homeowner installation. It's my understanding and it's clear from the documentation, that only professional HVAC people are supposed to install this.

Though you can install this without the Equipment Interface Module (EIM), I decided to wait, get the EIM, and then do the full installation. The first EIM I ordered was the wrong one, so you have to be careful about that. The EIM is installed next to your equipment, you run almost all the wires from your devices to the EIM and just a two-wire thermostat wire (for power) to the thermostat itself. Once powered up, the EIM, the thermostat, the outdoor remote, and the handheld remote can all start talking with each other over the air and things are swell from that point on.

I have a forced hot air, oil furnace, an air conditioner, and a powered bypass humidifier. I also got the optional return and supply air temperature sensors. Everything wires into the EIM: the humidifier can use one of three universal terminal pairs. When you setup the thermostat for the first time, you tell the thermostat what you have and what's wired to what ports on the EIM.

I did run into some quirks. When I opened up my furnace to find the power supply, I didn't realize the low voltage thermostat power is actually AC, not DC. I was carefully (I thought) testing everything as I went and ended up confused when I didn't read the voltages correctly on my meter. This was a rookie error. A professional installer would have known immediately that 24 volt AC power is used.

You are given the option of having the thermostat control the humidifier and run it even when the heat is not on. I have not been successful in implementing that option and the thermostat didn't run properly with that option set. Once I put the options back to the more typical situation where the humidifier only runs when the furnace is on, everything ran perfectly.

You have to enter a code to get to the installer options after you first set everything up. This code is not hard to find and if you read the installer instructions carefully, you can find it easily thereafter.

Once in place, the thermostat is excellent. It recovers from lost power without a hitch and no new programming or resetting is needed. The touch screen works very well. The options are plentiful and excellent. You can, for example, hit a button for "Stay home from work" and it will keep the heat on for you. Controlling the house heat using the remote control as your temperature sensor works very well. (I need this as the wall-mounted thermostat is affected when I have a good fire going in the fireplace formerly leaving the rest of the house freezing.)

I'm very pleased with the thermostat though I don't expect any help from Honeywell if something goes wrong.

**************** Update... three months later... ********************

I spent some time going through all the wiring on all my equipment. I found wiring diagrams for the furnace and air conditioner. I got better light into the nooks and crannies and took my time identifying everything on everything. I found it helpful to take pictures of items, load them onto my computer, and then blow them up to see details and to have everything in the same place.

The end result was that I found several places where technicians over the years had swapped wires here and there. Things worked with simpler thermostats but I think these swaps were causing problems with this fancier system.

I took my time, straightened out the wiring for the furnace, hooked it up, tested it, then did the same for the fan relay, then the A/C, then the humidifier. I tested things as I went and made sure I was matching all the wiring diagrams.

Bottom line was that I got it all working beautifully. I mentioned that the thermostat has a code-locked installer section. In that master menu, there are all sorts of sub-menus for setting up and testing the system. In the testing section, you can go through each component one by one and turn them on and off. If you have the sensors, you can check the temperature difference between return and discharge air. This was extremely helpful. There were times I was worried when testing the equipment without using this special testing section... things would work and then they wouldn't. Another rookie mistake on my part. The thermostat won't allow the A/C system to turn on then off and then on again in rapid sequence... that's to protect the equipment from rapid cycling. But that was also causing me to worry something had gone wrong when I couldn't fire things right back up. However, if you use the installer test section, the delay is bypassed and you can turn things on and off as necessary to check it all out.

Soooo.... I'm very pleased with this system. It ain't cheap, it ain't uncomplicated, and it ain't for the timid. But with some patience and skepticism of what technicians have done to your system in the past, you can get it all up and running and when you do, it's really, really good.

Click Here For Most Helpful Customer Reviews >>

This thermostat is a life saver as well as a money saver. We needed this thermostat for its remote sensing device. I have a two story house but only one zone heating and cooling. Our thermostat is located downstairs in a far corner of the house that is always cooler than the rest of the house. This makes it very difficult to keep a consistent heating temperature at night. Our upstairs would easily be 88 degrees at 4 am while the heater was trying to keep the downstairs at a mere 67 degrees. The remote sensing device can be taken anywhere in the house. With one touch of the button it can be told to sense temperature from its location. We do this every night to keep our bedrooms comfortable. We are now able to sleep again at night. Plus the downstairs doesn't get too cold either as the heat still falls. Great option to have. On top of all that, the setup is easy. It walks you through every possible option for setting up your schedules. The display looks great and the touchscreen is very responsive.

Best Deals on Honeywell YTHX9321R5061 Prestige® 2.0 HD Comfort System Kit

I am very happy with this thermostat. I replaced an existing 5 wire. I have 2 separate furnaces/AC that are single stage. I was intimidated when I saw a list of the installer options. I was worried that I would make a wrong choice or miss something. Not to worry. Once I selected "Conventional", only the options that pertained to my system showed up. It was a very quick and easy walk through the options. Make sure you shut the power off. Wire it up and off you go. I did have a worried moment when I was attaching the thermostat to the base. I clicked it in at the bottom and then tried to get the top to click in. It wasn't going. I was worried that if I pushed too hard I was going to break it. I had to push pretty hard but it clicked in.

I was up late that night and noticed that the upstairs display had turned to this faded out color and all the numbers were black instead of white. OMG, what did I do wrong? I pushed on the touch screen and it changed back to that beautiful blue. I went down and looked at the other thermostat and it was the same way. Looked in the manual and in the troubleshooting section, found out that it changes at 2AM for 1 hour to prevent burn in of the screen. WHEW!

I bought this thermostat because of the remote unit. It did not disappoint. If you can afford the extra bucks and you need the remote, it's a no brainer. I think it is worth it just for the display. Classy. So easy to use and program. No regrets.

Honest reviews on Honeywell YTHX9321R5061 Prestige® 2.0 HD Comfort System Kit

With all the hype Nest thermostats are getting I was a little reluctant to get this one. But I have to admit that especially with the Remote Sensor and Portable Remote control I am extremely happy with my purchase of the 2.0 kit. Its also nice that I can build more off of this kit. ie remote access. The only down side is that its a night light. I would prefer that the screen would turn off when inactive. But on the other end I can see from across the room what temperature the house is at any time. Oh and being a consumer (not knowing all the differences and details of versions) I had to return my original order for the 2.0 IAQ version so that it would work with my Air Exchanger and Humidifier.

Find helpful customer reviews and review ratings for Honeywell YTHX9321R5061 Prestige® 2.0 HD Comfort System Kit

We tried the Nest, but it wasn't good for us. It allows too much of a temperature swing. The Honeywell is extremely good at keeping the temperature consistent, and the ability to move the remote around as a thermostat is perfect for keeping the baby's room at the right temperature. Now we just set it and forget it. No more fiddling.

Buy Fom Amazon Now

Monday, June 23, 2014

Best Easy Heat EH-38 Freeze Thermostatically Controlled Valve and Pipe Deals

Easy Heat EH-38 Freeze Thermostatically Controlled Valve and Pipe Heating System
Customer Ratings: 4 stars
List Price: $19.99
Sale Price: $16.17
Today's Bonus: 19% Off
Buy Now

I bought this thermostat control for use with a heater for keeping a battery warm during the winter. Last winter the battery heater was always on to keep the battery warm to start an automatic generator. The heating during times when the temperature warmed up resulted in a damaged battery. This thermostat is just the right temperature range. After reading the negative review, I tested all three devices by cycling the temperature from 10-60 degrees F several times to verify they are working correctly.

Click Here For Most Helpful Customer Reviews >>

I purchased this device to back up the furnace in my cabin. I have it connected to an electric heater in the basement. So far my furnace has not failed, but I did have some air leaks that dropped my basement below 38 deg. and the device turned on as it should. Gives me peace of mind to know that as long as the electricity is on I will have some type of heat. I have it connected to a 1500 watt heater and there were no problems with mine. I have tested it several times by placing it outside in the cold and it has always worked.

Best Deals on Easy Heat EH-38 Freeze Thermostatically Controlled Valve and Pipe

I recorded temperatures with a wireless weather transmitter and it cut on and off around 38 and 50 degrees as advertised. Stopped working correctly after about 3 weeks, cutting on and off somewhat randomly at different temperatures. Once it started to malfunction it never stayed on long enough to warm the pump house. For something that often controls critical heat you would think reliability would be better.

Honest reviews on Easy Heat EH-38 Freeze Thermostatically Controlled Valve and Pipe

I bought the controller to operate a heat cable. It came on when the temperature got below 35 degrees but then it would turn on and off at below freezing temperatures for no reason at all. Luckily what I was using the heat cable on was not very critical.

Find helpful customer reviews and review ratings for Easy Heat EH-38 Freeze Thermostatically Controlled Valve and Pipe

I bought two of these one that turns on a fountain to keep a small pond from freezing, and another to regulate a heater to keep a small greenhouse temperature above freezing. Well, the first one works just fine for my purposes; it turns on around 36 degrees or so and turns off when the temperature outside gets to about 40, but the second is unusable for keeping the greenhouse in the 40 degree area. It won't turn on until it's about 32 and shuts off before it gets to 40. I was expecting a little margin of error (the literature says on at 38, off at 50), but not this much. So neither one really operates as advertised.

Buy Fom Amazon Now

Tuesday, March 4, 2014

Nesco American Harvest FD-1018P 1000 Watt Food Dehydrator Kit Reviews

Nesco American Harvest FD-1018P 1000 Watt Food Dehydrator Kit
Customer Ratings: 4.5 stars
List Price: $189.99
Sale Price: $138.72
Today's Bonus: 27% Off
Buy Now

Somewhere in my life I think in Boy Scouts I developed a taste for beef jerky. Years later, in grad school, I realized I could make it at home, as well as dry fruits and vegetables for snacks, with a magical machine called a dehydrator. At the time I picked up a cheap machine $24, I think from Wal-Mart. I was able to make some ground beef jerky, dry some fruits and make my own ground red pepper from peppers I grew in pots in the porch. Soon, the dehydrator lid was cracked, the trays warped, other things got my attention, and forming jerky strips from ground beef was tedious without a jerky gun, so the machine got put up for a number of years.

Six or seven years later, I'm in my career and new house. The interest in making jerky and drying foods is renewed, bolstered by an interest in drying foods for camping. I tried to use the old machine. It's only temperature control was a variable vent on the lid but you still didn't know what temperature you were drying at. (which can be the difference between safe jerky, and jerky that will make you quite sick) I'm probably lucky I never got sick. The airflow was also quite inconsistent. One end of an item would be overdried, while the other end wasn't dried at all. These things would just ruin entire batches of food. Additionally, there were no drying sheets available for it to make leathers ("fruit roll-ups," but you can also dry things like spaghetti sauce.) I decided to get a better dehydrator.

I researched dehydrators, and found several books and online reviews pointing to the American Harvest (NESCO) Gardenmaster. The FD-1018 and FD-1010 are the same machine, but the FD-1018 includes more trays, more leather sheets, more mesh sheets (a finer mesh than the tray which allows drying of smaller objects, like chopped veggies, without falling through the trays), and a book on drying.

The most important features of this dehydrator are the temperature control (dry veggies at 135-145F, meats at 145-155F), and the fact that it is carefully designed for uniform airflow on every sheet. This last advantage cannot be emphasized enough. With the Gardenmaster, I don't have to worry about moving items around and shuffling trays for consistent results. It's actually pretty amazing how well it works!

The Gardenmaster has been getting a workout making jerkies, fruit leathers, and dehydrating vegetables for taking to camp.

As for choosing the FD-1010 or FD-1018, if you're investing this kind of money, I'd highly recommend going to the FD-1018. The price difference more than made up for the cost of purchasing the additional trays, additional accessories and book separately (at least when I purchased it). You will find that you can EASILY fill a half dozen trays. (I used 5 trays the other night to dry just 2 lbs of ground beef jerky.) You don't want to overcrowd foods. You also get enough leather sheets for all of the trays and enough screens for all of the trays. It's frustrating to find that you have enough trays for your drying task, but only have 2 or 3 screens or sheets. The book HOW TO FRY FOODS by Delong is also included. I intend to cover that in an individual review, but it is a worthwhile book and much more substantial than the directions you'd otherwise receive with a dehydrator.

If you don't want to spend this kind of money until you see how much you'll use it, you may want to try the smaller NESCO FD-50 Snackmaster, which also has temperature control, although it only goes to 145F, which is the minimum for meat. As I said, NESCO seems to know the secret of uniform airflow, and I expect this knowledge to be extended to the FD-50.

Don't try to skimp too much on a dehydrator, or you will pay for ruined food, wasted time and frustration. If it is in your price range, you will no be disappoined with the FD-1018 Gardenmaster.

UPDATE: If you're upgrading to this from a less powerful model, beware that it may dry MUCH faster! I've ruined a couple of batches of jerky turned REALLY leathery before I realized I was OVERdrying! Can't leave it drying jerky overnight.

Click Here For Most Helpful Customer Reviews >>

I already own the FD-50 (the smaller version). I found myself wanting more capacity. I did a lot of research but had been so happy with the smaller Nesco I just decided to get its big brother with all the accessories (screens, trays)

I wasn't disappointed.

Preformance Same as the smaller version, Jerky in 4 hours, apple chips in 6. Higher capacity for sure but not night and day difference from the smaller one. This ones strenght comes in that you can stack a whole lot of trays.

Features A dehydrator with an off switch. What a concept. Put a timer on it and maybe you'll be in the 20th century! Why they can't put these things on is beyond me. I still use a light timer but at least now I don't have to unplug it.

Build One another area of improvement over it smaller brother. Seems to be built a lot better. Has more weight to it and just seems like a higher quality item.

If you want a deydrator to handle volume don't hesitate to get this one. Its got plenty of features, power and capacity.

Best Deals on Nesco American Harvest FD-1018P 1000 Watt Food Dehydrator Kit

If you are tired of paying too much for dried fruit at the store I strongly recommend a dehydrator. I chose this one based on the good reivews and I haven't been disappointed. Special Note: the more trays the better! To limit drying time I slice fruit very thin so that takes up more trys. Also, there is work involved in the prep and clean up so why not get most fruit out of a single drying session? This is not a quiet item so plan on using it in a different room.

Pros: Great product, easy to use, easy to clean

Cons: Noisy, Out of date booklet.

Special Note: Dried honeydew mellon is wonderful!

Honest reviews on Nesco American Harvest FD-1018P 1000 Watt Food Dehydrator Kit

The important aspects to look for when looking for a good dehydrator are accurate temperature control, good air flow, and adequate space for the amount of food that you want to dehydrate. I strongly feel that this machine does a superb job fulfilling each of those criteria.

I've had this dehydrator for awhile now, and have pretty much put everything I have in my kitchen into it. I've made tons of beef, elk, and deer jerky with great results. I've dried carrots, peas, corn, tomatoes, garlic, onions, star fruit, pears, strawberries, grapes (into raisins), bell peppers, jalepenos, and various garden herbs. I've even made my own chicken base with this thing. It's great.

In a home kitchen, some may complain about it being a little loud. That should be expected seeing as it is nothing more than a fan and a heating coil with a bunch of plastic trays stacked on top. I think it takes up too much space to keep in the kitchen or living room anyway, so I store mine in the basement where it can make all the noise in the world without bothering anyone. I have used this at work in the professional kitchen, and with the humming and whirling of the vents and ovens and other noise makers throughout the kitchen, it seems virtually noise free.

I've had it running non-stop for as long as a six weeks straight while drying out my garden in preparation for the winter, and have not noticed any problems with over heating or wear. As simple of a design as it is, it seems to be built fairly solid. I'm definitely happy with my investment.

Find helpful customer reviews and review ratings for Nesco American Harvest FD-1018P 1000 Watt Food Dehydrator Kit

A couple years ago I bought the Ronco and reviewed it (the review is way back there now). I took my own advice and bought this Nesco and oh man am I happy!

I can do three times the amount Jerky in half the time as with the Ronco and don't have to worry about the trays cracking while washing. If you are considering paying the extra $$$ for the Nesco over the Ronco, don't. It's a no-brainer. The Nesco does more Jerky faster, eliminates the need to turn the racks, and you don't have to use kid gloves to handle the trays.

Highly, highly recommended.

Buy Fom Amazon Now

Friday, February 7, 2014

Review of 2GIG CT-30 Radio Thermostat Z-Wave

2GIG CT-30 Radio Thermostat Z-Wave
Customer Ratings: 4 stars
Buy Now
This is a special version of ZWave designed for vivint and would not work properly on my Honneywell Lynx system's ZWave.

Click Here For Most Helpful Customer Reviews >>

This item works very well with my Mi Casa Verde Lite module. Simple to installed. Took me less that 10 minutes.

Best Deals on 2GIG CT-30 Radio Thermostat Z-Wave

Since I received this Thermostat, I never had an issue with it. I love the fact that it can be used on battery only as I do not currently have power going to my Thermostat.

Honest reviews on 2GIG CT-30 Radio Thermostat Z-Wave

Works great with my ADT Pulse. It is programmable through Pulse to set the temp when I arm or disarm the alarm to my desired temp. Never have to worry if I changed the temp when I leave the house.

Buy Fom Amazon Now