This product turned out to work perfectly. It arrived on time and it works as it should. A quartz heater is the only solution for a loft where you need to heat the room rather than all the heat going upstairs!
However, this particular quartz heater (unlike the ones I've had before) is fan-forced, which in my opinion is not as desirable because of the noise issue. It is not noisy as some fan heaters, but I would have preferred the quiet kind, they works just as well. Maybe in my enthusiasm, I didn't check that very carefully...I don't remember seeing 'fan-forced' in the description but I could be wrong.....anyway, that's why I am changing my rating to 4.
A.
Showing posts with label web thermostat. Show all posts
Showing posts with label web thermostat. Show all posts
Sunday, February 1, 2015
Wednesday, January 21, 2015
Buy Honeywell/Aube TH115-AF-240S Programmable Thermostat for Electric
Installed 4 of these thermostats on under-tile heated floors in entrance, two bathrooms, and kitchen. Nice to be able to set floor and air temperature independently (to some extent), and to quickly turn it down by using the away button without need for manual adjustments or reprogramming.
Monday, December 1, 2014
Cheap Mr. Induction SR-182C 1800-Watt Countertop Commercial Range
Customer Ratings: 
List Price: $449.00
Sale Price: $355.03
Today's Bonus: 21% Off

I got this induction unit about a month ago as education while we ponder a kitchen remodel. I currently have a gas cooktop, with all its pros and cons, but in view of all the positive reviews for induction I had to give it a try. Bottom line up front: It's a keeper, but mostly because I don't think there is an induction burner that's better, not because I'm particularly impressed. I do like the way the heat goes only into the pan and that cleaning the surface is much simpler than getting down under the grate of a gas stove.
I first got the Duxtop equivalent to Mr. Induction, but returned it because I couldn't find a decent simmer with its 10 heating levels. This model has 20 levels, which is much better but still not the continuous control that I'd like. In the "cook" mode, level 1, the lowest, is just above a simmer. In the "temp" mode simmer is easier to find (more about that below), but I'm still not fully happy with the control of induction vs. gas. It would be nice if there were a few levels below the heat level of "1" on this burner. On the other hand, browning onions on the 12-15 range of "cook" is excellent, and 5-7 is a good fit to medium heat called for in recipes.
In the "Temp" mode, 180 F is close to a simmer, 200 F is bubbling well above a simmer, and 170 F shows no bubble at all, much less than a simmer. So, again, I'd like more control around the boiling point in both modes. Perhaps asking that boiling is close to 212 F is being too particular. I'd be happy with the offset if there were finer control around boiling.
Two other points I find to be less than ideal: The heating element is about 3/4-inch off center toward the control panel. This is just annoying to the perfectionist who may prefer the pan centered on the rings on the top surface (see photo), but one wonders how it could happen. Finally, the burner is sitting on a very level counter, but without correction fluids (oil, butter, scrambled eggs) flow toward the back of the pan. Adding a couple of 1/8" thick felt pads to the back legs levels the unit and has the added advantage that it can be easily slid back out of the way when not in use or brought close to the counter edge for cooking by simply picking up the front legs and sliding on the felt pads at the back. The standard rubber feet do not slide on the counter, by design.
Yes, there are many low-temperature setting, perhaps good for melting chocolate, etc. In the "temp" mode there are several settings below boiling, the lowest of which is "90 F." However, the temperature control does not seem to be proportional; the unit appears to be either on or off. I have not accurately measured the temperature overshoot and undershoot while this cycling occurs, but I'll bet it's substantial.
A final note: because the heating appears to happen in a circle of 4.5" diameter, it helps to have pots with thick conductive bases to spread the heat over more of the pan bottom. Cuisinart GreenGourmet Tri-Ply and Zwilling J.A. Henckels Thermolon Spirit cookware do a pretty good job. I'll review these as I get more experience with them and their competitors.
On balance, I'm intrigued by induction, but I hope it can be better than demonstrated by this burner. From what I can glean from induction cooktop ads, most of them do have a limited number of power settings, which limits control. I don't know if any have proportional temperature control. Please reply if you know of any. My remodel will likely have both gas and induction modules if I can find an induction module with continuous heat control and proportional temperature control, but I'm not holding my breath.
List Price: $449.00
Sale Price: $355.03
Today's Bonus: 21% Off
I got this induction unit about a month ago as education while we ponder a kitchen remodel. I currently have a gas cooktop, with all its pros and cons, but in view of all the positive reviews for induction I had to give it a try. Bottom line up front: It's a keeper, but mostly because I don't think there is an induction burner that's better, not because I'm particularly impressed. I do like the way the heat goes only into the pan and that cleaning the surface is much simpler than getting down under the grate of a gas stove.
I first got the Duxtop equivalent to Mr. Induction, but returned it because I couldn't find a decent simmer with its 10 heating levels. This model has 20 levels, which is much better but still not the continuous control that I'd like. In the "cook" mode, level 1, the lowest, is just above a simmer. In the "temp" mode simmer is easier to find (more about that below), but I'm still not fully happy with the control of induction vs. gas. It would be nice if there were a few levels below the heat level of "1" on this burner. On the other hand, browning onions on the 12-15 range of "cook" is excellent, and 5-7 is a good fit to medium heat called for in recipes.
In the "Temp" mode, 180 F is close to a simmer, 200 F is bubbling well above a simmer, and 170 F shows no bubble at all, much less than a simmer. So, again, I'd like more control around the boiling point in both modes. Perhaps asking that boiling is close to 212 F is being too particular. I'd be happy with the offset if there were finer control around boiling.
Two other points I find to be less than ideal: The heating element is about 3/4-inch off center toward the control panel. This is just annoying to the perfectionist who may prefer the pan centered on the rings on the top surface (see photo), but one wonders how it could happen. Finally, the burner is sitting on a very level counter, but without correction fluids (oil, butter, scrambled eggs) flow toward the back of the pan. Adding a couple of 1/8" thick felt pads to the back legs levels the unit and has the added advantage that it can be easily slid back out of the way when not in use or brought close to the counter edge for cooking by simply picking up the front legs and sliding on the felt pads at the back. The standard rubber feet do not slide on the counter, by design.
Yes, there are many low-temperature setting, perhaps good for melting chocolate, etc. In the "temp" mode there are several settings below boiling, the lowest of which is "90 F." However, the temperature control does not seem to be proportional; the unit appears to be either on or off. I have not accurately measured the temperature overshoot and undershoot while this cycling occurs, but I'll bet it's substantial.
A final note: because the heating appears to happen in a circle of 4.5" diameter, it helps to have pots with thick conductive bases to spread the heat over more of the pan bottom. Cuisinart GreenGourmet Tri-Ply and Zwilling J.A. Henckels Thermolon Spirit cookware do a pretty good job. I'll review these as I get more experience with them and their competitors.
On balance, I'm intrigued by induction, but I hope it can be better than demonstrated by this burner. From what I can glean from induction cooktop ads, most of them do have a limited number of power settings, which limits control. I don't know if any have proportional temperature control. Please reply if you know of any. My remodel will likely have both gas and induction modules if I can find an induction module with continuous heat control and proportional temperature control, but I'm not holding my breath.
Tuesday, November 11, 2014
ElectroWarmth Heated Mattress Pads Reviews
I'm a big fan of heated mattress pads (vs electric blankets). They seem to last longer (I've had several electric blankets break in the last few years), the heat is more even, and I like the heat from below rather than above. I've used an electric mattress pad on my own bed for several years now and been very happy with it. I picked up this twin-size pad for my 8 year old son, who was envious of my warm bed. He loves it! We turn it on about 15 minutes before bed, and he always climbs into a warm bed. We usually turn it off after he gets into bed, but on some cold nights he's left it on "Low" and gone right to sleep. It's a great feeling to have a warm bed, especially when the house is cold!
Update, 3 years later:
Unlike other electric blankets and mattress warmers I've purchased over the last 15 or so years, this one is STILL heating like new! I do have a couple of gripes that may or may not be issues for you:
The skirt that keeps the warmer snug against the mattress is a bit flimsy. After seasonally changing it a few times, the stitching ripped out along one edge. Ever since, I've been careful to treat it gently, and it hasn't gotten worse, so just remember to actually walk around your mattress to remove it from each corner, and don't try to whip it off the corners from the opposite side of the bed. But this isn't why I've lowered my rating.
You can't use this warmer with a timer or any sort of remote-operated outlet (like a home-automation, x-10, z-wave, insteon, or wifi outlet, or even a switched outlet). If the power to your outlet has been off, and gets switched on, the warmer still has to be manually turned on with its controls. Why is this a big issue for me? Well, I've been installing home-automation switches and outlets so that I can turn devices on and off with my iPhone, and this is definitely one of those devices that I want to control remotely (or even put on a timer). I frequently forget to trudge upstairs and turn the warmer on an hour before bed, and I'd like to be able to do it while watching TV downstairs, or simply have the knowledge that a simple timer will do it for me. Hence, I'm dinging them, in the hope that you, like I, find 3-star reviews to be the ones with the most helpful information for otherwise potentially great products.
I spoke with an Electrowarmth representative who said that this feature has been requested (although infrequently), and that she knew of no plans to alter the functionality. If this feature is important to you, please call them and request it!
Suffice it to say, Electrowarmth delivers a fine quality USA made safe product that works exactly as advertised. It warms to set temp in about 10 minutes or so and keeps it constant all night. The fully electronic control means no annoying clicks and it is softly lit when you press the temperature buttons. The light glows for about 10 or so seconds then goes off.
The unit will run 10 hours once you turn it on. If you turn off but leave it plugged in, it will remember your last setting from L to H with 1-9 in between.
The only disadvantage I can see is the fact the wiring on the control means it is placed backward on the nightstand.
Given the fact I sleep with a comforter and a cotton top blanket, the setting marked 4 is more than enough to warm the mattress.
The cords are amply long to reach from bottom of bed to unit and still reach an outlet close by. It is machine washable and UL listed.
I recommend this product made in America, highly.
Update, 3 years later:
Unlike other electric blankets and mattress warmers I've purchased over the last 15 or so years, this one is STILL heating like new! I do have a couple of gripes that may or may not be issues for you:
The skirt that keeps the warmer snug against the mattress is a bit flimsy. After seasonally changing it a few times, the stitching ripped out along one edge. Ever since, I've been careful to treat it gently, and it hasn't gotten worse, so just remember to actually walk around your mattress to remove it from each corner, and don't try to whip it off the corners from the opposite side of the bed. But this isn't why I've lowered my rating.
You can't use this warmer with a timer or any sort of remote-operated outlet (like a home-automation, x-10, z-wave, insteon, or wifi outlet, or even a switched outlet). If the power to your outlet has been off, and gets switched on, the warmer still has to be manually turned on with its controls. Why is this a big issue for me? Well, I've been installing home-automation switches and outlets so that I can turn devices on and off with my iPhone, and this is definitely one of those devices that I want to control remotely (or even put on a timer). I frequently forget to trudge upstairs and turn the warmer on an hour before bed, and I'd like to be able to do it while watching TV downstairs, or simply have the knowledge that a simple timer will do it for me. Hence, I'm dinging them, in the hope that you, like I, find 3-star reviews to be the ones with the most helpful information for otherwise potentially great products.
I spoke with an Electrowarmth representative who said that this feature has been requested (although infrequently), and that she knew of no plans to alter the functionality. If this feature is important to you, please call them and request it!
Click Here For Most Helpful Customer Reviews >>
Having tired of climbing into a cold bed during the winter and having to crank up the expensive to run furnace, I was interested in a quality heated mattress pad.Suffice it to say, Electrowarmth delivers a fine quality USA made safe product that works exactly as advertised. It warms to set temp in about 10 minutes or so and keeps it constant all night. The fully electronic control means no annoying clicks and it is softly lit when you press the temperature buttons. The light glows for about 10 or so seconds then goes off.
The unit will run 10 hours once you turn it on. If you turn off but leave it plugged in, it will remember your last setting from L to H with 1-9 in between.
The only disadvantage I can see is the fact the wiring on the control means it is placed backward on the nightstand.
Given the fact I sleep with a comforter and a cotton top blanket, the setting marked 4 is more than enough to warm the mattress.
The cords are amply long to reach from bottom of bed to unit and still reach an outlet close by. It is machine washable and UL listed.
I recommend this product made in America, highly.
Best Deals on ElectroWarmth Heated Mattress Pads
I purchased this queen mattress pad because it had the option of having only one remote and that's what I really wanted. It was intended to be for my second home as I already have one in my main home. When I opened this pad today I could immediately feel the wires in it right through the fabric. It also has a big direction/warning sheet (approx 6x8 in size) that's made of very stiff paper right on the top corner of the pad so when you are in bed, it would end up being right under your pillow where you could certainly feel it (and hear it) through your sheet. After paying twice the amount as I did my original mattress pad, I would expect at least equal or better quality. This one is already in the package to be returned. The cheaper pads out there are far better than this one!Honest reviews on ElectroWarmth Heated Mattress Pads
The pad is well construced. The duel control for the full size bed was a must and glad to have found one. The heating is great. But we have a problem. We can't keep the bottom sheet in place due to the shiny and slippery covering of the pad. It is a constant battle. Every time one of us turns over or moves around the sheet either bunches up or comes off the edges, top, bottom or sides. Very aggravating. We would like to have a solution. We have tried different sheet fabrics.Find helpful customer reviews and review ratings for ElectroWarmth Heated Mattress Pads
Works well, warms the bed nice... one review said the tag was on the top, and they could feel it while sleeping. Ours is at the bottom, don't even know it's there. Wires are barely noticeable.Tuesday, October 7, 2014
Review of Pelonis Classic Ceramic Heater
Customer Ratings: 
List Price: $99.99
Sale Price: $74.21
Today's Bonus: 26% Off

With dozens of so called "ceramic" portable heaters on the market it can be very difficult to sort through all the models. Here are the facts friends; Pelonis (Del Rain) pionerred the original fully ceramic portable heaters back in the mid 80's...these models use 100% ceramic heating (disc design) elements and will approximately double the amount of heat available, watt for watt, than all other so called "ceramic" heaters. Why the confusion? the lower cost units (20-30$) use very small ceramic conductive elements which are then joined to long metal type heating fins; (there is only an upfront cost saving); the pelonis disc furnace will pay for itself in less than one heating season! And, by the way, our own space shuttles employ this same type of heating unit on their missions. Case dismissed.
We still have it and it works great.
I have bought over 25 Pelonis furnaces since then. They originally called them furnaces for a reason. Here are the pros and cons. The ones with forced air are not as good as the true ceramic. The ones with out the ceramic discs are not any better than other cheap heaters. The Original ceramic only are excellent par anything They heat up the rooms in our trailer from 25 degrees to 75 degrees 10x12 rooms) and turn off automatically in about 15 minutes. That is unbelieveable The heat penetrates into the furniture and into you. It is not just ehating the air it heats the contents of the room. We did get a black plastic one and it did melt the case when we had it too close to a metal item but oh well, it still runs 10 years later!!! I recommend the original Pelonis with temp control, the browm metal box type. We have had the newer styles and oscilating and no it is not like the original for sure. Thanks for listening
I bought the same model twenty years ago and was extremely happy with it. Comparing it with the new model there is no comparison. The new one is built really cheap and flimsy. The are lots of plastic parts with the new one. My old was made in the USA while the new one now made in China.
List Price: $99.99
Sale Price: $74.21
Today's Bonus: 26% Off
With dozens of so called "ceramic" portable heaters on the market it can be very difficult to sort through all the models. Here are the facts friends; Pelonis (Del Rain) pionerred the original fully ceramic portable heaters back in the mid 80's...these models use 100% ceramic heating (disc design) elements and will approximately double the amount of heat available, watt for watt, than all other so called "ceramic" heaters. Why the confusion? the lower cost units (20-30$) use very small ceramic conductive elements which are then joined to long metal type heating fins; (there is only an upfront cost saving); the pelonis disc furnace will pay for itself in less than one heating season! And, by the way, our own space shuttles employ this same type of heating unit on their missions. Case dismissed.
Click Here For Most Helpful Customer Reviews >>
The Pelonis Disc Furnace is the most efficient and safest small space heater ever built. Dispite their small size, they can easily heat a large room.Best Deals on Pelonis Classic Ceramic Heater
The B-6A1 ceramic space heater is one of the best I have used over many years experience...It far exceeds those which cost less, such as the one's offered at Lowe's, Home Depot, K-Mart, Wal-Mart and elsewhere...In my opinion it is better buildt and puts out more heat than others...It is also far quieter and has a varible temp. selector...You will find that this heater cost more, but you only get what you pay for...It will give you years of good service..Honest reviews on Pelonis Classic Ceramic Heater
My Dad bought an original Peopnis disc furnace in 1982 because it was used on NASA flights to heat the spacecrafts. How cold does it get up there???We still have it and it works great.
I have bought over 25 Pelonis furnaces since then. They originally called them furnaces for a reason. Here are the pros and cons. The ones with forced air are not as good as the true ceramic. The ones with out the ceramic discs are not any better than other cheap heaters. The Original ceramic only are excellent par anything They heat up the rooms in our trailer from 25 degrees to 75 degrees 10x12 rooms) and turn off automatically in about 15 minutes. That is unbelieveable The heat penetrates into the furniture and into you. It is not just ehating the air it heats the contents of the room. We did get a black plastic one and it did melt the case when we had it too close to a metal item but oh well, it still runs 10 years later!!! I recommend the original Pelonis with temp control, the browm metal box type. We have had the newer styles and oscilating and no it is not like the original for sure. Thanks for listening
Find helpful customer reviews and review ratings for Pelonis Classic Ceramic Heater
Do not buy this heater or any Pelonis product. I bought this heater two months ago. I turned this heater on and it burned my linoleum floor. I tried calling the number on their web site and it just rings and rings. I sent an email to them and I have not received a response.I bought the same model twenty years ago and was extremely happy with it. Comparing it with the new model there is no comparison. The new one is built really cheap and flimsy. The are lots of plastic parts with the new one. My old was made in the USA while the new one now made in China.
Tuesday, August 19, 2014
Discount Princess 182666 Stainless Steel Deep Fryer with Warming Drawer
I purchased this fryer in mid 2011 but have only used it about 10 times. I have always kept in clean and with fresh oil. Now it is only about a year later and it will not power up. I tried the reset and it just will not work. Was not worth the money in my opinion.I recieved the deep fryer as stated in a timely manner, and in perfect shape. I have only used it once and it was easy to use. I have not tried out the warming drawer yet.
Sunday, June 22, 2014
Review of Sengoku SP-160 Mini Panel Electric Heater. 150 Watt
Customer Ratings: 
List Price: $69.99
Sale Price: $47.45
Today's Bonus: 32% Off

I don't know why Amazon.com is using a drawing of a bathroom vanity instead of a photo of this great little heat panel. Visit other sites to see what it really looks like. Photos show it as a grey panel with rounded corners. This is accurate, but what the photos don't show is that the front surface is covered with a soft, felt-like covering which adds to the warmth of this little gem. The back is just metal. It heats up quickly and silently and radiates warmth almost instantly. It would easily fit under a desk. It's hard to believe it only uses 150 watts of electricity. I like this unit better than others I've looked at, since it comes with attachable feet and the on/off switch has a red light to remind you that it's on. The switch and light are on the right side and can be easily seen from the front. I'm very pleased with it. But keep in mind, it's meant to be close to you, and it probably won't help heat up an entire room. Still, the warmth it radiates is impressive.
It works "okay" and emits a constant, small, soothing amount of heat, but does not get real warm.
I was finding myself pulling it between my legs. Then it felt much warmer. (Heat comes out both sides.)
I was sensible when I purchased it knowing that it is only 150 Watts ... there is only so much heat that a unit of that size will throw.
What I did next was the "ticket" to total and complete warmth for my feet under my desk!
After this purchase, I purchased a heated floor mat. (Foot Warmer – Cozy Toes – 18"W x 19"D x 1/2"H)
That floor mat product is excellent and gets very warm.
I now use the 2 products together and I'm extremely happy.
This heating panel is definitely better than nothing, but If I could recommend one or the other, it would be the floor mat. It emits much more heat directly to the feet.
I hope this was helpful!
: -)
List Price: $69.99
Sale Price: $47.45
Today's Bonus: 32% Off
I don't know why Amazon.com is using a drawing of a bathroom vanity instead of a photo of this great little heat panel. Visit other sites to see what it really looks like. Photos show it as a grey panel with rounded corners. This is accurate, but what the photos don't show is that the front surface is covered with a soft, felt-like covering which adds to the warmth of this little gem. The back is just metal. It heats up quickly and silently and radiates warmth almost instantly. It would easily fit under a desk. It's hard to believe it only uses 150 watts of electricity. I like this unit better than others I've looked at, since it comes with attachable feet and the on/off switch has a red light to remind you that it's on. The switch and light are on the right side and can be easily seen from the front. I'm very pleased with it. But keep in mind, it's meant to be close to you, and it probably won't help heat up an entire room. Still, the warmth it radiates is impressive.
Click Here For Most Helpful Customer Reviews >>
Wonderful, warm, safe, uses barely any electricity, and adds just that right amount of warmth to one person (on top of normal house heating). Great if you have one person in a household who gets cold, but the other people are not cold. Great if you sit at a desk all day and want a heat source near you that is safe. Will help heat up a very small bedroom easily.Best Deals on Sengoku SP-160 Mini Panel Electric Heater. 150 Watt
Great Heater for under your desk. Delivers the right amount of extra heat. Not made for high heat output.Honest reviews on Sengoku SP-160 Mini Panel Electric Heater. 150 Watt
I purchased this for under my desk in my home office as my feet are always cold.It works "okay" and emits a constant, small, soothing amount of heat, but does not get real warm.
I was finding myself pulling it between my legs. Then it felt much warmer. (Heat comes out both sides.)
I was sensible when I purchased it knowing that it is only 150 Watts ... there is only so much heat that a unit of that size will throw.
What I did next was the "ticket" to total and complete warmth for my feet under my desk!
After this purchase, I purchased a heated floor mat. (Foot Warmer – Cozy Toes – 18"W x 19"D x 1/2"H)
That floor mat product is excellent and gets very warm.
I now use the 2 products together and I'm extremely happy.
This heating panel is definitely better than nothing, but If I could recommend one or the other, it would be the floor mat. It emits much more heat directly to the feet.
I hope this was helpful!
: -)
Find helpful customer reviews and review ratings for Sengoku SP-160 Mini Panel Electric Heater. 150 Watt
This is a great little heater if you need to heat a small enclosed space or simply provide some extra warmth to an area. I use this heater for my birds. I was forced to move them into the basement and this heater allowed me to do that without compromising their health. The birds can bathe, relax, and play without getting too cold or too hot. There is no temperature adjustment but, really, it doesn't need it. The front gets hot but not enough to really catch fire or burn someone right away. Although, leaving your hand there for a few seconds might result in a minor burn. The lighted on/off switch is a nice touch. Overall, I like it so far... we'll see how long it lasts.Sunday, May 4, 2014
Best Kegorator Beer Keg Fridge Deals
Customer Ratings: 
List Price: $499.99
Sale Price: $474.33
Today's Bonus: 5% Off

For starters, stop reading reviews prior to 2011. The early issues with this kegerator have been addressed to the point Nostalgia really should assign it a new model number. As reported by others the regulator is now a pretty nice dual gauge unit, with a lockable output valve. Meaning once you get your CO2 settings dialed in you can lock the knob so it doesn't get changed accidentally while changing out a keg, etc. Also, the unit is dead quiet.
The instructions have been completely revamped and are very easy to follow. All the spare parts provided have been labeled in the manual, no mysteries there either. Before this arrived I downloaded a PDF copy of the old instructions, and it's true the early buyers were basically left in the dark.
I followed the instructions, charged my tank, threw in a 1/4 barrel, and no problems at all. The beer has a perfect head on it, and my monitoring of temps have been hovering around 34-35f. That's with the thermostat set to maximum, so I'll be watching that closely. I don't want my beer to freeze!
A few things to note:
1) The keg tower rubber washer (#5) was not already installed, and is not really mentioned in the manual. Be sure to install it otherwise there's not a tight seal between the tower and fridge and cool air will escape. You'll know if it's not on because the tower installs too easy and doesn't feel tight. The nice side effect of this design is that the tower is basically cooled, so less stale beer in the line.
2) A 5 pound CO2 tank will fit with a full 1/2 barrel, and can be bought at a local gas supply or welding shop filled for about 50 bucks. Refills on the tank are around $9. The 2.5 pound tank shipped is fine, and I'll be filling it so I have a full tank at all times. The 2.5 pound tank should be able to dispense 2-4 1/2 barrel kegs, the 5 pound tank 4-8 1/2 barrel kegs. Tighter fittings, lower CO2 settings, more kegs...
3) The casters are optional, and there are already self leveling feet installed if (like me) you prefer the unit to be shorter and stationary. Height to the top of the fridge door is exactly 31 inches without the caster installed.
Anyway, given all the features and the insane price of $380 shipped I can't see how anyone could be unhappy at this point. All the negative reviews made me really ponder this purchase, but I'm happy to report they're all talking about a different product. I'll post a follow up at 12 months, or before if I experience any problems.
And thanks to the early buyers who posted reviews! Nostalgia listened and thanks to you I have a really nice unit.
----------------
This is an excellent kegerator. We purchased it as a Christmas gift for my dad, and we are currently on our second half-barrel of lager! I was a bit skeptical of this based on previous reviews, but as many reviews state, Nostalgia had changed some parts and old issues are no longer present with this model.
LOOKS
We all think it's a good looking unit. Nostalgia offers the same unit but with a stainless steel door. I decided against the stainless steel model because we currently have stainless steel appliances and they show smudges and fingerprints easily. We keep the kegerator in our garage so the black is more appropriate. This unit also features a rounded front door, so the keg partially hangs out when the door is open. Most other kegerators have a flat door, which makes the whole unit looks larger. It is also not the highest quality appliance you will find, as the internals of this unit seem to be a bit plasticky, especially next to a nice, expensive refrigerator. But if you temper your expectations, you will be very happy with it.
ASSEMBLY
The instructions are a bit frustrating. Each section doesn't seem to be in proper order. Also, there are plenty of extra little parts that come with it. I still don't know where they all go, but it's good to have them I guess. My best advice to get it up and running as soon as possible:
* first have a keg ready to go (call a local beer store, and have them order and hold a keg of your favorite beer until you're ready for it--it may take a few days for them to get the keg if it is not in stock).
* Unbox the unit and put the casters on (not too tightly or they will be difficult to spin).
* Plug it in and turn the thermostat to the coldest setting.
* Get your Co2 tank filled up. I took mine to a paintball place, but you can also try a welding or outdoor sport shop. If you're still stuck, call a hardware store for some suggestions. Also, the beer store you're getting your keg from may swap Co2 tanks.
Take your time with assembly and read the instructions carefully. It may be a bit frustrating at times with all the different sized washers and parts, but keep at it and you will work through it just fine. At first, I used nylon tape on the fittings, but later found that there is no point to this, as the various washers in place are there to stop leaks, rendering the nylon tape unnecessary--but there is no harm in doing so. I had a tough time getting the tower on with the rubber washer (the instructions didn't say to put it on but it is in the parts bag, and the tower doesn't fit right without it). I recommend putting some dish soap on both sides of the washer, put it in place, stand on the left side (when you're facing the unit) and hold the unit in place with your knee while you push down hard and turn the tower clockwise until it locks. It may take a few tries and some effort but it eventually fits snug and will help keep cold air in.
REGULATOR
Past complaints have been about the regulator. The old regulator was a single gauge--this newer one is a dual gauge. After a few months of usage, I decided to replace the regulator due to it allowing the keg to become over-pressurized despite my low-psi setting. The Co2 pressure SHOULD remain constant throughout the life of your Co2--if you are constantly fighting the pressure, get rid of the regulator and buy a new one. Over-pressurizing your keg will waste Co2 and end up costing you more money and frustration anyway. After some research, regulators from Micromatic seem to be held in high regard, so I went ahead and purchased one from their website (dual-guage, premium, part #642). If you do purchase a new regulator, remember to get a new gas line and barbed tip so you can connect it to the keg coupler--Micromatic sells all of this. I've had zero issues since changing the regulator. Also, the regulator I purchased was a bit larger than the stock one, so it may be a tight fit depending on your keg and Co2 tank sizes.
Remember that when you have a new keg, the keg is already pressurized somewhat, so you will need very little Co2 pressure through the first few pours until the keg pressure is relieved, or alternatively relieve the pressure using the pressure relief valve on the tap. After that, you will have slower pours, which is your cue to turn up the pressure. Don't turn it up too high or else you will get foamy pours. There is a relief valve on the regulator to reset the pressure which is helpful during adjusting. There is another relief valve on the keg tap as well, which can also help troublesome pours. This kegerator comes with a 5lb Co2 tank, but it was quickly swapped out for a larger tank. It may be a good idea down the road to get a 10lb tank and keep the included smaller tank as a spare.
Another note: always remember to use a nylon washer between your Co2 tank and the regulator. Failing to use a nylon washer will result in a leak. If you swap your tank at a beer store, they will likely give you a washer. The Micromatic regulator I've described above has a permanent washer in place.
THERMOSTAT
Some reviewers wrote about modifying the thermostat by removing the cover on the thermostat and adjusting the little screw. I would recommend taking a wait and see approach to determine whether you need to do this--you don't want to adjust it too much and unnecessarily freeze up your beer (most beer freezes around 28-29 degrees). I ended up waiting 24 hours before I gave the adjustment screw a clockwise turn, waited a few hours, then checked again (my keg was hovering around 40 degrees, I was shooting for about 36). After the adjustment, the temp has been steady around 36.
THERMOSTAT ADJUSTMENT
Here is how to get to the adjustment screw: first, unplug the unit, then on the back of the unit, turn the temperature dial to the max setting, then pull the knob off. Now, remove the two screws that hold the thermostat housing to the side of the kegerator. Then remove the two screws to take the thermostat off of the housing. Then on the thermostat, there is a small phillips screw above the temperature adjustment dial. Turn it once clockwise to go colder, counter-clockwise to go warmer (just one turn was all I needed). Put everything back together, plug the unit back in, then wait a couple of hours before you check the temperature and make another adjustment as necessary.
After a year of ownership, the kegerator has remained cool and reliable.
CLEANING
An important topic that I did not previously cover in my original review. Make sure you buy a nice kegerator cleaning kit (I recommend this one: Beer Line Cleaning Kit). You will want to keep the beer lines clean, otherwise, bacteria from the beer line can creep back into the beer, causing the beer to go bad. I recommend cleaning the lines after every keg change--it's a simple process of disconnecting the lines and running a cleaning solution through the lines, as well as disconnecting the tap and cleaning some of the little parts. There are also little parts for attaching to the tap to cover the tap opening when not in use for extended periods of time--they can be easily found on Amazon.
I have not had any shipping/packaging issues that other reviewers spoke of. I also have not had any reason to contact Nostalgia customer support.
NOTES: Some issues people commonly have, especially when they are new to kegs, are that the beer either comes out too slow (which basically means you're out of Co2 or don't have enough pressure), or the beer comes out too fast (meaning too much Co2 is in the keg), resulting in a foamy mess. Firstly, your regulator has two gauges--one, (the left side) gauge, shows the pressure coming from your Co2 tank, and the other (the top gauge), shows the pressure you are delivering to the keg. Typically, the left-side Co2 tank gauge reads anywhere from 500 to 1000 bar psi (which will vary on the tank temperature), and it is perfectly normal for the tank to read in this range when it has enough Co2. When your tank begins to run out, it will quickly hit zero. And when you're setting up a new keg, the pressure may fluctuate a bit as the system normalizes, so while the correct pressure may be set once you first hook up a fresh keg, checking back an hour or two later, you may notice it needs readjusting. This is normal.
Now, in the event that you over-pressurize your keg, it means you have way too much Co2 in there, and as a result, your beer will come out very fast and very foamy. Some reviewers blame this on the kegerator, but really it is their own fault. The simple solution is this: close the valve on your Co2 tank as well as close the switch on your regulator. Then, find the relief pin on your keg tap (you have two relief pins--one on the regulator, one on the keg tap). Pull this pin hard (helpful if you use a pair of pliers) and it will slowly release the pressure in your keg. It may take a minute or two, but the pressure will slowly die down. When the pressure is relieved, start pouring beer until the pour is too slow (it may even take a few pitchers more of foamy beer, but it will get there--be patient). Finally, when the pour is too slow, open your Co2 tank valve, then turn on the regulator switch to the open position as well, and finally slowly adjust your Co2 on the regulator until you get a nice pour. It may take a while and readjusting in an hour or two, but be patient!
Finally, when your keg is kicked, close off the valve on your Co2 tank as well as the switch on the regulator to avoid losing any Co2.
Overall, I think you will be very happy with this unit. It's one of the cheapest ones you'll find on the internet, so as long as you take your time setting it up and do your research on this unit to find out its quirks, you will be happily pouring fresh, draft beer in no time!
Cheers!
Thermostat does not keep the beer cold enough false, I've had to turn down the fridge because it was TOO cold. Did not modify it at all.
Regulator only has one gauge false, this kegerator came with a dual gauge regulator.
Slow shipment false, ordered with prime, shipped 3 hours after I ordered it, packaged very well.
CO2 tank held by cheap band false, CO2 tank is held by a plastic mesh and fits very nicely in the back.
Overall this has surpassed by expectations for a kegerator under $400
1. The instuctions are a little vague, but try to follow them and the recommendations of others. There are lots of extra little gaskets and misc. parts that are shipped with your unit. Don't panic and think you've missed a step.
2. As recomended, use teflon tape on all fittings.
3. It doesn't tell you in the manual, but do as others recommende and USE the rubber gasket when you install the beer dispenser tower. I sprayed the gasket with WD-40 first. It was still a bit of work to twist and lock the tower, but if you omit installing this gasket, you'll lose cold air.
4. When you first instal your CO2 tank to set your pressure, be sure to turn the regulator valve all the way off, the open the tank valve (just one turn), then open your regulator valve to the required pressue (7-11 psi). I found it easier to set the preferred pressure at the CO2 valve and when it stabilized, I used the allen wrench to lock the regulator valve at that pressure. Note: Be patient when making this adjustment. Turn it slighly and wait for it to stabilize.
5. I was one of the unfortunate few who's kegorator did not get cold enough at first. The coldest it got was 40 degrees with it turned to MAX and waiting overnight for it to cool down. I followed the recommendation of others, removed the thermostat housing and thermostat, adjusted the screw a few turns clockwise and reinstalled thermostat. Now the temperature sits at 36 degrees with the thermostat set just a 1/2" before the max setting.
Now for the not so good part. After all was said and done (e.g. correct temperature and CO2 pressure), I tapped my keg and discovered that I had a faulty beer line. It had a pin hole at the 90-degree bend of the beer line tail piece. Beer went everywhere which of course rendered the unit unuseable. I called the number in the instruction booklet, explainded my issue and they sent a complete beer tower at no cost. BTW, I went ahead a purchased a replacement metal tail piece at a local Home Brew store, cut the plastic tube, inserted the new piece, clamped it down with one of the 'extra' clamps provided and it works fine. I have an extra beer tower just in case.
I now have ice cold Yuengling Lager on tap. So, if you follow the recommendation of others, and with a little patience, you shouldn't have many, if any, issues.
Update: It's been well over a year and my Kegorator is still working like a charm. Cold, cold beer! Cheers.
List Price: $499.99
Sale Price: $474.33
Today's Bonus: 5% Off
For starters, stop reading reviews prior to 2011. The early issues with this kegerator have been addressed to the point Nostalgia really should assign it a new model number. As reported by others the regulator is now a pretty nice dual gauge unit, with a lockable output valve. Meaning once you get your CO2 settings dialed in you can lock the knob so it doesn't get changed accidentally while changing out a keg, etc. Also, the unit is dead quiet.
The instructions have been completely revamped and are very easy to follow. All the spare parts provided have been labeled in the manual, no mysteries there either. Before this arrived I downloaded a PDF copy of the old instructions, and it's true the early buyers were basically left in the dark.
I followed the instructions, charged my tank, threw in a 1/4 barrel, and no problems at all. The beer has a perfect head on it, and my monitoring of temps have been hovering around 34-35f. That's with the thermostat set to maximum, so I'll be watching that closely. I don't want my beer to freeze!
A few things to note:
1) The keg tower rubber washer (#5) was not already installed, and is not really mentioned in the manual. Be sure to install it otherwise there's not a tight seal between the tower and fridge and cool air will escape. You'll know if it's not on because the tower installs too easy and doesn't feel tight. The nice side effect of this design is that the tower is basically cooled, so less stale beer in the line.
2) A 5 pound CO2 tank will fit with a full 1/2 barrel, and can be bought at a local gas supply or welding shop filled for about 50 bucks. Refills on the tank are around $9. The 2.5 pound tank shipped is fine, and I'll be filling it so I have a full tank at all times. The 2.5 pound tank should be able to dispense 2-4 1/2 barrel kegs, the 5 pound tank 4-8 1/2 barrel kegs. Tighter fittings, lower CO2 settings, more kegs...
3) The casters are optional, and there are already self leveling feet installed if (like me) you prefer the unit to be shorter and stationary. Height to the top of the fridge door is exactly 31 inches without the caster installed.
Anyway, given all the features and the insane price of $380 shipped I can't see how anyone could be unhappy at this point. All the negative reviews made me really ponder this purchase, but I'm happy to report they're all talking about a different product. I'll post a follow up at 12 months, or before if I experience any problems.
And thanks to the early buyers who posted reviews! Nostalgia listened and thanks to you I have a really nice unit.
Click Here For Most Helpful Customer Reviews >>
NOTE: I've updated this post in March of 2013, after a year of ownership. My basic feelings of the kegerator are still the same--but I just wanted to update some of the information provided in this review. In summary, I did end up replacing the regulator with a higher-quality one.----------------
This is an excellent kegerator. We purchased it as a Christmas gift for my dad, and we are currently on our second half-barrel of lager! I was a bit skeptical of this based on previous reviews, but as many reviews state, Nostalgia had changed some parts and old issues are no longer present with this model.
LOOKS
We all think it's a good looking unit. Nostalgia offers the same unit but with a stainless steel door. I decided against the stainless steel model because we currently have stainless steel appliances and they show smudges and fingerprints easily. We keep the kegerator in our garage so the black is more appropriate. This unit also features a rounded front door, so the keg partially hangs out when the door is open. Most other kegerators have a flat door, which makes the whole unit looks larger. It is also not the highest quality appliance you will find, as the internals of this unit seem to be a bit plasticky, especially next to a nice, expensive refrigerator. But if you temper your expectations, you will be very happy with it.
ASSEMBLY
The instructions are a bit frustrating. Each section doesn't seem to be in proper order. Also, there are plenty of extra little parts that come with it. I still don't know where they all go, but it's good to have them I guess. My best advice to get it up and running as soon as possible:
* first have a keg ready to go (call a local beer store, and have them order and hold a keg of your favorite beer until you're ready for it--it may take a few days for them to get the keg if it is not in stock).
* Unbox the unit and put the casters on (not too tightly or they will be difficult to spin).
* Plug it in and turn the thermostat to the coldest setting.
* Get your Co2 tank filled up. I took mine to a paintball place, but you can also try a welding or outdoor sport shop. If you're still stuck, call a hardware store for some suggestions. Also, the beer store you're getting your keg from may swap Co2 tanks.
Take your time with assembly and read the instructions carefully. It may be a bit frustrating at times with all the different sized washers and parts, but keep at it and you will work through it just fine. At first, I used nylon tape on the fittings, but later found that there is no point to this, as the various washers in place are there to stop leaks, rendering the nylon tape unnecessary--but there is no harm in doing so. I had a tough time getting the tower on with the rubber washer (the instructions didn't say to put it on but it is in the parts bag, and the tower doesn't fit right without it). I recommend putting some dish soap on both sides of the washer, put it in place, stand on the left side (when you're facing the unit) and hold the unit in place with your knee while you push down hard and turn the tower clockwise until it locks. It may take a few tries and some effort but it eventually fits snug and will help keep cold air in.
REGULATOR
Past complaints have been about the regulator. The old regulator was a single gauge--this newer one is a dual gauge. After a few months of usage, I decided to replace the regulator due to it allowing the keg to become over-pressurized despite my low-psi setting. The Co2 pressure SHOULD remain constant throughout the life of your Co2--if you are constantly fighting the pressure, get rid of the regulator and buy a new one. Over-pressurizing your keg will waste Co2 and end up costing you more money and frustration anyway. After some research, regulators from Micromatic seem to be held in high regard, so I went ahead and purchased one from their website (dual-guage, premium, part #642). If you do purchase a new regulator, remember to get a new gas line and barbed tip so you can connect it to the keg coupler--Micromatic sells all of this. I've had zero issues since changing the regulator. Also, the regulator I purchased was a bit larger than the stock one, so it may be a tight fit depending on your keg and Co2 tank sizes.
Remember that when you have a new keg, the keg is already pressurized somewhat, so you will need very little Co2 pressure through the first few pours until the keg pressure is relieved, or alternatively relieve the pressure using the pressure relief valve on the tap. After that, you will have slower pours, which is your cue to turn up the pressure. Don't turn it up too high or else you will get foamy pours. There is a relief valve on the regulator to reset the pressure which is helpful during adjusting. There is another relief valve on the keg tap as well, which can also help troublesome pours. This kegerator comes with a 5lb Co2 tank, but it was quickly swapped out for a larger tank. It may be a good idea down the road to get a 10lb tank and keep the included smaller tank as a spare.
Another note: always remember to use a nylon washer between your Co2 tank and the regulator. Failing to use a nylon washer will result in a leak. If you swap your tank at a beer store, they will likely give you a washer. The Micromatic regulator I've described above has a permanent washer in place.
THERMOSTAT
Some reviewers wrote about modifying the thermostat by removing the cover on the thermostat and adjusting the little screw. I would recommend taking a wait and see approach to determine whether you need to do this--you don't want to adjust it too much and unnecessarily freeze up your beer (most beer freezes around 28-29 degrees). I ended up waiting 24 hours before I gave the adjustment screw a clockwise turn, waited a few hours, then checked again (my keg was hovering around 40 degrees, I was shooting for about 36). After the adjustment, the temp has been steady around 36.
THERMOSTAT ADJUSTMENT
Here is how to get to the adjustment screw: first, unplug the unit, then on the back of the unit, turn the temperature dial to the max setting, then pull the knob off. Now, remove the two screws that hold the thermostat housing to the side of the kegerator. Then remove the two screws to take the thermostat off of the housing. Then on the thermostat, there is a small phillips screw above the temperature adjustment dial. Turn it once clockwise to go colder, counter-clockwise to go warmer (just one turn was all I needed). Put everything back together, plug the unit back in, then wait a couple of hours before you check the temperature and make another adjustment as necessary.
After a year of ownership, the kegerator has remained cool and reliable.
CLEANING
An important topic that I did not previously cover in my original review. Make sure you buy a nice kegerator cleaning kit (I recommend this one: Beer Line Cleaning Kit). You will want to keep the beer lines clean, otherwise, bacteria from the beer line can creep back into the beer, causing the beer to go bad. I recommend cleaning the lines after every keg change--it's a simple process of disconnecting the lines and running a cleaning solution through the lines, as well as disconnecting the tap and cleaning some of the little parts. There are also little parts for attaching to the tap to cover the tap opening when not in use for extended periods of time--they can be easily found on Amazon.
I have not had any shipping/packaging issues that other reviewers spoke of. I also have not had any reason to contact Nostalgia customer support.
NOTES: Some issues people commonly have, especially when they are new to kegs, are that the beer either comes out too slow (which basically means you're out of Co2 or don't have enough pressure), or the beer comes out too fast (meaning too much Co2 is in the keg), resulting in a foamy mess. Firstly, your regulator has two gauges--one, (the left side) gauge, shows the pressure coming from your Co2 tank, and the other (the top gauge), shows the pressure you are delivering to the keg. Typically, the left-side Co2 tank gauge reads anywhere from 500 to 1000 bar psi (which will vary on the tank temperature), and it is perfectly normal for the tank to read in this range when it has enough Co2. When your tank begins to run out, it will quickly hit zero. And when you're setting up a new keg, the pressure may fluctuate a bit as the system normalizes, so while the correct pressure may be set once you first hook up a fresh keg, checking back an hour or two later, you may notice it needs readjusting. This is normal.
Now, in the event that you over-pressurize your keg, it means you have way too much Co2 in there, and as a result, your beer will come out very fast and very foamy. Some reviewers blame this on the kegerator, but really it is their own fault. The simple solution is this: close the valve on your Co2 tank as well as close the switch on your regulator. Then, find the relief pin on your keg tap (you have two relief pins--one on the regulator, one on the keg tap). Pull this pin hard (helpful if you use a pair of pliers) and it will slowly release the pressure in your keg. It may take a minute or two, but the pressure will slowly die down. When the pressure is relieved, start pouring beer until the pour is too slow (it may even take a few pitchers more of foamy beer, but it will get there--be patient). Finally, when the pour is too slow, open your Co2 tank valve, then turn on the regulator switch to the open position as well, and finally slowly adjust your Co2 on the regulator until you get a nice pour. It may take a while and readjusting in an hour or two, but be patient!
Finally, when your keg is kicked, close off the valve on your Co2 tank as well as the switch on the regulator to avoid losing any Co2.
Overall, I think you will be very happy with this unit. It's one of the cheapest ones you'll find on the internet, so as long as you take your time setting it up and do your research on this unit to find out its quirks, you will be happily pouring fresh, draft beer in no time!
Cheers!
Best Deals on Kegorator Beer Keg Fridge
I was a little hesitant buying this kegerator because of some of the bad reviews it received from this site and others. However, I trusted Amazon to take the return if it came in broken or did not perform. I've had this item for about 2 weeks now and I have to say it works beautifully. If you are concerned about the following items don't be:Thermostat does not keep the beer cold enough false, I've had to turn down the fridge because it was TOO cold. Did not modify it at all.
Regulator only has one gauge false, this kegerator came with a dual gauge regulator.
Slow shipment false, ordered with prime, shipped 3 hours after I ordered it, packaged very well.
CO2 tank held by cheap band false, CO2 tank is held by a plastic mesh and fits very nicely in the back.
Overall this has surpassed by expectations for a kegerator under $400
Honest reviews on Kegorator Beer Keg Fridge
I too was a little skeptical at first, but it all worked out fine. First off; read, read, read others reviews for installation tips. I did and it all worked out for the best. First off, if you're going to go ahead and upgrade to a 5-gal CO2 tank, do it and order at the same time you order your kegorator. You'll end up saving a few dollars. I didn't and instead of paying $60 through Amazon, I paid $90 + tax for an empty tank. Here are more recommendations:1. The instuctions are a little vague, but try to follow them and the recommendations of others. There are lots of extra little gaskets and misc. parts that are shipped with your unit. Don't panic and think you've missed a step.
2. As recomended, use teflon tape on all fittings.
3. It doesn't tell you in the manual, but do as others recommende and USE the rubber gasket when you install the beer dispenser tower. I sprayed the gasket with WD-40 first. It was still a bit of work to twist and lock the tower, but if you omit installing this gasket, you'll lose cold air.
4. When you first instal your CO2 tank to set your pressure, be sure to turn the regulator valve all the way off, the open the tank valve (just one turn), then open your regulator valve to the required pressue (7-11 psi). I found it easier to set the preferred pressure at the CO2 valve and when it stabilized, I used the allen wrench to lock the regulator valve at that pressure. Note: Be patient when making this adjustment. Turn it slighly and wait for it to stabilize.
5. I was one of the unfortunate few who's kegorator did not get cold enough at first. The coldest it got was 40 degrees with it turned to MAX and waiting overnight for it to cool down. I followed the recommendation of others, removed the thermostat housing and thermostat, adjusted the screw a few turns clockwise and reinstalled thermostat. Now the temperature sits at 36 degrees with the thermostat set just a 1/2" before the max setting.
Now for the not so good part. After all was said and done (e.g. correct temperature and CO2 pressure), I tapped my keg and discovered that I had a faulty beer line. It had a pin hole at the 90-degree bend of the beer line tail piece. Beer went everywhere which of course rendered the unit unuseable. I called the number in the instruction booklet, explainded my issue and they sent a complete beer tower at no cost. BTW, I went ahead a purchased a replacement metal tail piece at a local Home Brew store, cut the plastic tube, inserted the new piece, clamped it down with one of the 'extra' clamps provided and it works fine. I have an extra beer tower just in case.
I now have ice cold Yuengling Lager on tap. So, if you follow the recommendation of others, and with a little patience, you shouldn't have many, if any, issues.
Update: It's been well over a year and my Kegorator is still working like a charm. Cold, cold beer! Cheers.
Find helpful customer reviews and review ratings for Kegorator Beer Keg Fridge
I ordered this item on September 14th. Didn't get delivered until October 4th. Way out of the time range that was initially given. Product information made it appear that all you would need to do is supply the Keg and get the CO2 tank filled. WAY OFF. The "regulator" that comes with the Kegerator doesn't regulate ANYTHING its simply an off on switch for the CO2. After spending 2 days wasting beer I took it to my local tavern and confirmed what I already thought. So I had to drive to my local Beer Supply store and spend an additional $50 for an actual regulator. Then I experienced the problem that any regulator you buy doesn't connect to the supplied air hose as it should. Next stop Ace hardware where i purchased new tubing and fittings (another $10 down the drain). Upon affixing my new regulator and air hoses I realized that the beer comes out WAY too fast causing an excessive amount of foam. Last trip to Ace Hardware and got a water flow restricter for another $3 and now at long last i finally have a fully operational kegerator. Cheers and have fun.Monday, March 31, 2014
Best Southern Enterprises Sicilian Harvest Black Electric Fireplace Deals
Customer Ratings: 
List Price: $864.99
Sale Price: $460.09
Today's Bonus: 47% Off

I have been looking for a nice large electric fireplace for about 2 years under $500. This one came and it is great! It is large enough to make a statement and have a prominent place in the room. The assembly took me about 1.5 hours and was not that difficult -you just need a screwdriver. The heater on the fireplace produces heat immediately and warms a room about 20'x20' nicely. Various settings for the flames, logs, and heater -it's simply wonderful for a snowy day!
I would recommend this fireplace to anyone who is looking to supplement their furnace heat to save on costs. And also for anyone who wants to add a little coziness to any room in their house.
List Price: $864.99
Sale Price: $460.09
Today's Bonus: 47% Off
I have been looking for a nice large electric fireplace for about 2 years under $500. This one came and it is great! It is large enough to make a statement and have a prominent place in the room. The assembly took me about 1.5 hours and was not that difficult -you just need a screwdriver. The heater on the fireplace produces heat immediately and warms a room about 20'x20' nicely. Various settings for the flames, logs, and heater -it's simply wonderful for a snowy day!
Click Here For Most Helpful Customer Reviews >>
I love my electric fireplace!!!! Had to receive the heater and the base separately(2 shipments) and i had only received the base! Called and they sent me the heater right away! I set it up in our bedroom and it heats up the room right away! We have left it all night on and i love that my electric bill has been less compared to when we had a little heater! Would most def buy again, a bit pricey but well worth the $Best Deals on Southern Enterprises Sicilian Harvest Black Electric Fireplace
It shipped fast, arrived safe, and was easy to set up. Have had no problems with it and we are extremely happy with it.Honest reviews on Southern Enterprises Sicilian Harvest Black Electric Fireplace
This is a very nice fireplace bought to put in a finished family room in the basement and it looks great. Although it has been very hot this summer, I tried the heater for about 30 minutes and it puts out nice warmth think it will be pefect to keep the room cozy this winter. HOWEVER, beware Amazon advertised this as 12 month free financing and it was not. When I called customer service, they told me that I was at least the 5th person they had talked to that had misunderstood the way that Amazon was advertising the deferred financing.Find helpful customer reviews and review ratings for Southern Enterprises Sicilian Harvest Black Electric Fireplace
I really like this little guy. It was easy to assemble. It cranks out some serious heat. So far so good. The only complaint I have about it, is that the grill on the front gets REALLY hot when it's turned on. I guess it makes it more like a real fireplace! :)I would recommend this fireplace to anyone who is looking to supplement their furnace heat to save on costs. And also for anyone who wants to add a little coziness to any room in their house.
Saturday, February 22, 2014
Discount niceEshop® LCD Digital Thermometer for Refrigerator/Fridge/Freezer
Customer Ratings: 
List Price: $8.33
Sale Price: $5.46
Today's Bonus: 34% Off

I ordered two of these thermometers. Subtract one star because the product description clearly states a 2 second sampling rate and 1.2 meter wire. The little slip of paper that comes with the thermometers clearly states a sampling rate of 10 seconds. Testing revealed a sampling rate of 9 seconds. The wire on both thermometers measured 29 inches. That's a lot shorter than 1.2 meters.
Subtract another star for quirky electronics. Each thermometer shipped with two batteries. The battery compartment holds two batteries. I installed the batteries in one thermometer. Nothing happened! No worky! I installed the other two batteries into the second thermometer. Nothing happened! While trying to resolve the issue, one of the batteries fell out. Low and behold, the thermometer turns on. I then removed one of the batteries from the second thermometer. That one started working too. The thermometers work if you install only one of the two required batteries. Oddest thing I've ever seen.
In addition to testing the sampling rate, I also tested precision and accuracy. The two thermometers stayed within two tenths of a degree as I moved them from room temp to freezer to refrigerator. Both thermometers were within two degrees of the temperature as measured by other thermometers. This works for me.
Be forewarned, these are shipping from China. Two other sellers have an identical product under different listings. I chose this seller because it did NOT specify the item as being shipped from overseas. On May 1, I received a shipment notification email with an expected delivery date of June 12!!! Luckily, they arrived on May 11.
I wanted a thermometer to mount on the outside of the new freezer so I could keep
tabs on the temperature and I figured that $5 was not too much to invest. It works
great and I couldn't have asked for much more. That is, after I got used to the
fact that it only displays in Centigrade. Not really a big deal. I just had to
make a simple calculation to see what zero fahrenheit was in Centigrade. I
can really recommend this little thermometer.
List Price: $8.33
Sale Price: $5.46
Today's Bonus: 34% Off
I ordered two of these thermometers. Subtract one star because the product description clearly states a 2 second sampling rate and 1.2 meter wire. The little slip of paper that comes with the thermometers clearly states a sampling rate of 10 seconds. Testing revealed a sampling rate of 9 seconds. The wire on both thermometers measured 29 inches. That's a lot shorter than 1.2 meters.
Subtract another star for quirky electronics. Each thermometer shipped with two batteries. The battery compartment holds two batteries. I installed the batteries in one thermometer. Nothing happened! No worky! I installed the other two batteries into the second thermometer. Nothing happened! While trying to resolve the issue, one of the batteries fell out. Low and behold, the thermometer turns on. I then removed one of the batteries from the second thermometer. That one started working too. The thermometers work if you install only one of the two required batteries. Oddest thing I've ever seen.
In addition to testing the sampling rate, I also tested precision and accuracy. The two thermometers stayed within two tenths of a degree as I moved them from room temp to freezer to refrigerator. Both thermometers were within two degrees of the temperature as measured by other thermometers. This works for me.
Be forewarned, these are shipping from China. Two other sellers have an identical product under different listings. I chose this seller because it did NOT specify the item as being shipped from overseas. On May 1, I received a shipment notification email with an expected delivery date of June 12!!! Luckily, they arrived on May 11.
Click Here For Most Helpful Customer Reviews >>
I bought a new freezer after my old one quit on me and I lost $100 worth of meat.I wanted a thermometer to mount on the outside of the new freezer so I could keep
tabs on the temperature and I figured that $5 was not too much to invest. It works
great and I couldn't have asked for much more. That is, after I got used to the
fact that it only displays in Centigrade. Not really a big deal. I just had to
make a simple calculation to see what zero fahrenheit was in Centigrade. I
can really recommend this little thermometer.
Best Deals on niceEshop® LCD Digital Thermometer for Refrigerator/Fridge/Freezer
I bought 2 of these hoping to use them for my beer brewing activities (monitoring mash temperature and fermenting temp). After installing the LR44 batteries that came with them, I sat the side by side on my desk. After 10 minutes they were different by 5 degrees. I then put them both in my refrigerator, and they were still 5 degrees apart. What gives? Which one is correct? Guess I need to go back to the good old stick thermometer to calibrate these.Honest reviews on niceEshop® LCD Digital Thermometer for Refrigerator/Fridge/Freezer
Actually would have been great for twice the price. Works and appears to be fairly accurate compared to another thermometer I own.. either that or they are both screwed up the same way :-).Find helpful customer reviews and review ratings for niceEshop® LCD Digital Thermometer for Refrigerator/Fridge/Freezer
Beware it is only reading in Centigrade and not Fahrenheit, it has no on /off . the instructions was for another product. I hope the battery's last a year or better.Friday, February 7, 2014
Review of 2GIG CT-30 Radio Thermostat Z-Wave
This is a special version of ZWave designed for vivint and would not work properly on my Honneywell Lynx system's ZWave.
Click Here For Most Helpful Customer Reviews >>
This item works very well with my Mi Casa Verde Lite module. Simple to installed. Took me less that 10 minutes.Best Deals on 2GIG CT-30 Radio Thermostat Z-Wave
Since I received this Thermostat, I never had an issue with it. I love the fact that it can be used on battery only as I do not currently have power going to my Thermostat.Honest reviews on 2GIG CT-30 Radio Thermostat Z-Wave
Works great with my ADT Pulse. It is programmable through Pulse to set the temp when I arm or disarm the alarm to my desired temp. Never have to worry if I changed the temp when I leave the house.Thursday, February 6, 2014
Reviews of Chaney Instrument 00985 Wireless Refrigerator Freezer Thermometer
Customer Ratings: 
List Price: $34.99
Sale Price: $29.99
Today's Bonus: 14% Off

We bought this alarm because we have young kids who love to be independent and help out by getting their own ice and food. Since our indoor freezer is a bottom pull-out, they can get into it easily. We also have an upright freezer in the garage. We had one week where a freezer was left open three times. This alarm has helped tremendously.
We are using both sensors in the two freezers. They come pre-programmed with min/max settings, one for the refrigerator and one for the freezer. It is very simple to change those settings though and the directions were clear.
I really like that it has a fifteen-minute delay before the alarm sounds. That is, the temperature has to be above the set point for 15 minutes before the alarm is triggered. That feature prevents false alarms when a 3-year old is having trouble deciding which ice cube is the perfect one for his juice.
I wish I had known that for freezer use you need to use lithium batteries (AA) as they work at lower temperatures versus alkaline. We didn't have any on hand and so had to wait to install the units. Extra trips to the store are a pain and I would have just ordered 4 (2 for ea) when I bought the unit if I had known.
Setup instructions for the Chaney 00985 thermometer are very simple and easy to follow. I had the batteries installed, and the sensors in place in less than 10 minutes. We decided to utilize the magnetic mounting of the receiver, and stuck it directly to the outside of the refrigerator door. Within a couple of minutes, the freezer sensor registered with the receiver, showing a temperature of 58°F. I knew the freezer was no higher than zero degrees, but I figured it would likely take several minutes for the sensor to adjust to the drastic temperature change. Ten minutes later I checked again and the freezer was still showing 58°F and the refrigerator sensor still hadn't registered with the receiver. After waiting an hour, the freezer temp showed 52°F and the refrigerator finally registered but showed a temp of 67°F. WOW, how crazy is that? I removed the batteries and started over. This time both sensors registered within the first 10 minutes, but after an hour they were still showing in the 50s and 60s.
Over the course of several hours we changed the location of the receiver and sensors, and I even went out and purchased a new set of batteries (at nearly $10.00 for a 4-pack of lithium AAs). Many times the sensors wouldn't register with the receiver at all, unless I had them extremely close together (I'm talking within one foot of each other). The only way I could get this product to work is if I took the remote sensors out of the refrigerator and freezer compartments and placed them right next to the receiver. I am not exaggerating at all here folks, the sensors had to be literally within inches of the receiver in order to register and provide fairly accurate temperature readings. It eventually became clear to me that this product will not work at all with the sensors in the refrigerator and freezer compartments at all. Isn't this supposed to be the whole purpose of this product, to measure the internal temperatures of a refrigerator and freezer?
I don't know if our new refrigerator/freezer came with some sort of doors that the signal could not penetrate, but obviously this product would not work for us and I feel that the wireless signal they use is extremely poor. Amazon was great about letting me return this device, but now my wife and I cannot find any other wireless device to replace it with. There are a couple of others on the market, but they receive rather poor ratings as well and we are afraid to take a chance on them. I really, REALLY wanted to like the Chaney 00985 Wireless Refrigerator Freezer Thermometer. It looks awesome and the features of this product are exactly what we have been looking for. However, this device is obviously made of extremely poor quality, and I recommend that anyone who decides to purchase this product should keep the packaging and receipt handy, as it is likely you will end up needing to return it. I would gladly pay three times as much for this product if it would work reliably. In the meantime, if anyone knows of a product like this that is proven to work well, please let me know. Thank you.
------
SET-UP
------
The set-up was easy. I put the AA-Lithium batteries in the sensors first, and then the AAA-Lithium batteries into the base and within 1 minute it had registered both sensors and started working.
--------
ACCURACY
--------
This was my biggest concern given some of the other comments. However, with both sensors side by side on a table, they both read within 1 degree of each other, and both matched my external room thermometer. Good enough for me!
Then I placed them in my fridge and freezer. They took about 15 minutes to acclamatize and then started reading exactly the same as the readouts built in to the fridge.
--------
RANGE
--------
This was the key point for me. I needed something that was going to have range, as I don't want to have the main base attached to the outside of the door.
With the base attached to the door, no problem they worked fine.
With the base 20ft away and in the next room also worked great.
When I moved one of the sensors out of the freezer and into a room down the hall (about 35ft away) it stopped registering that one, but still read the other in the fridge (20ft away) I suspect the multiple walls were blocking the signal.
The one negative I would say about this, is that unlike the Orgagon Scientific thermometers I've used, this base unit provides no indication that it has lost contact with the sensor. I'd suggest that if it doesn't get an update within 2 minutes, it should show that on the screen somehow. Instead, this unit just keeps showing the last known temp -not very helpful.
Also, once it has lost it's connection, it seems that you have to remove the batteries or hit the paperclip sized reset button on the main base to re-initiate the connection.
-------
ALARMS
-------
Dead simple to set and exactly what I needed.
----------
BATTERIES
----------
I saw somebody else complained in a review that you have to use expensive lithium batteries in the sensors. That's a little silly isn't it? It's hardly the manufacturers fault that alkaline batteries would freeze in the freezer and not function.
My only complaint (and admitedly it's also a bit dumb) is that Amazon shipped the batteries in a separate box and 2 days later than the actual thermometers, so I had it sitting here for two days while I wanted to try it. See, told you it was dumb.
-----------------------
In closing, I think this is a good product. It seems well constructed. The mounting options of suction cups or spring clips on the sensors and wall hanging or magnets on the base are appreciated.
The only things that would make this a 5 star in my opinion are:
indicate when you've lost a signal
make the base available in silver and/or black
sell as a bundle with your first set of lithium batteries included.
I'm now going to take it out to my RV where I really need it. I will edit this if I have any future problems.
I'd buy it again...
Jay.
The Chaney Refrigerator / Freezer Thermometer is a brilliant way to keep an eye on how your food is doing. Here is how it works. You get one thermometer which you put into the back of your refrigerator. A second thermometer goes into the back of your freezer. Both of these send signals *wirelessly* to a display unit. The display unit is magnetic and can stick easily to the front of your refrigerator.
You can walk by your fridge and see at a glance exactly what temperature your fridge and freezer are currently at. The system also displays the highest and lowest temperature each area has reached since you last reset the values. So if you set your fridge normally to 34F and you see that it has been swinging between 20F and 50F, it's time to call a repair person! That would definitely cause serious damage to your food.
In addition, you can set alarm values, both high and low, for both sensors. So you can set the freezer to start beeping an alarm if it drops below -50F, or if it goes up above 0F. Of course the chance of your freezer suddenly going insane and becoming "way too cold" is probably slim but I know a number of people who had electrical problems with their fridges and who lost cooling ability without realizing it at first. Having a beeping alarm go off before your freezer's contents all thaw is a very good thing!
The wireless unit says that it can transmit a fair distance, but this of course would depend on all sorts of things if there are concrete walls between the source and destination, if there are other interfering signals around, and so on. For me, I know it works with the display on the outside of the fridge it is monitoring. So I can say with great certainty that that works very well.
I know for sure the alarm works wonderfully only a few weeks after buying the unit, we had a thunderstorm take out the power. It was only a short while later when the fridge half of our unit began beeping.
Is there a downside to this? Well, when we first got the set, the display LEDs simply would not light up well. We tried at least 8 different sets of batteries in it to ensure it wasn't a bad set of batteries. Some of the number pieces would light up, while others would stay completely unlit. We called up Chaney and they were extremely prompt and helpful. Only a few days later we had a fully functional display unit in our hands, and it worked beautifully. Electronic devices will never be 100% foolproof so I don't ding them much for having that glitch, and offer praise for them resolving it so readily.
All in all, I love this device. I can glance at my fridge every time I use it and know exactly what its temperature is and what the recent ranges of temperature have been. I can optimize the fridge and freezer to have the optimal temperatures to keep my food and wine fresh for as long as possible. That means milk lasts longer, salad fixings last longer, everything lasts longer. That stretches my food dollar as well as it can be stretched, and easily pays for the price of the thermometer within a month or two.
Highly recommended. I'm even looking into getting another one for my wine fridges. The only question then would be if the wireless transmitters interfere with each other!
List Price: $34.99
Sale Price: $29.99
Today's Bonus: 14% Off
We bought this alarm because we have young kids who love to be independent and help out by getting their own ice and food. Since our indoor freezer is a bottom pull-out, they can get into it easily. We also have an upright freezer in the garage. We had one week where a freezer was left open three times. This alarm has helped tremendously.
We are using both sensors in the two freezers. They come pre-programmed with min/max settings, one for the refrigerator and one for the freezer. It is very simple to change those settings though and the directions were clear.
I really like that it has a fifteen-minute delay before the alarm sounds. That is, the temperature has to be above the set point for 15 minutes before the alarm is triggered. That feature prevents false alarms when a 3-year old is having trouble deciding which ice cube is the perfect one for his juice.
I wish I had known that for freezer use you need to use lithium batteries (AA) as they work at lower temperatures versus alkaline. We didn't have any on hand and so had to wait to install the units. Extra trips to the store are a pain and I would have just ordered 4 (2 for ea) when I bought the unit if I had known.
Click Here For Most Helpful Customer Reviews >>
Purchased to monitor 2 freezers that are 60 feet apart. Though the manufacturer says that the display can be as far as 100 feet from the sensors I find that with intervening walls and doors the distance is reduced to about 40 feet. Found a convenient location half-way between both freezers and all works well. A great temperature monitoring system that can be used to monitor 2 freezers, 2 refrigerators or 1 of each.Best Deals on Chaney Instrument 00985 Wireless Refrigerator Freezer Thermometer
After having one of our refrigerators freeze up and go out on us recently, we had water all over the floor and we lost quite a bit of food products. As we do not spend much time in the area where this refrigerator is, we had no idea it had gone out for quite some time. After purchasing a new refrigerator/freezer, we didn't want to take the chance of another disaster like this, so we searched for a thermometer and alarm system that would allow for an external display with separate internal temperature sensors for the refrigerator and freezer compartments. Every site we checked pointed to the Chaney 00985 Wireless Refrigerator Freezer Thermometer, so we eagerly ordered one. We also picked up a 4-pack of Lithium AA batteries to power the remote sensors.Setup instructions for the Chaney 00985 thermometer are very simple and easy to follow. I had the batteries installed, and the sensors in place in less than 10 minutes. We decided to utilize the magnetic mounting of the receiver, and stuck it directly to the outside of the refrigerator door. Within a couple of minutes, the freezer sensor registered with the receiver, showing a temperature of 58°F. I knew the freezer was no higher than zero degrees, but I figured it would likely take several minutes for the sensor to adjust to the drastic temperature change. Ten minutes later I checked again and the freezer was still showing 58°F and the refrigerator sensor still hadn't registered with the receiver. After waiting an hour, the freezer temp showed 52°F and the refrigerator finally registered but showed a temp of 67°F. WOW, how crazy is that? I removed the batteries and started over. This time both sensors registered within the first 10 minutes, but after an hour they were still showing in the 50s and 60s.
Over the course of several hours we changed the location of the receiver and sensors, and I even went out and purchased a new set of batteries (at nearly $10.00 for a 4-pack of lithium AAs). Many times the sensors wouldn't register with the receiver at all, unless I had them extremely close together (I'm talking within one foot of each other). The only way I could get this product to work is if I took the remote sensors out of the refrigerator and freezer compartments and placed them right next to the receiver. I am not exaggerating at all here folks, the sensors had to be literally within inches of the receiver in order to register and provide fairly accurate temperature readings. It eventually became clear to me that this product will not work at all with the sensors in the refrigerator and freezer compartments at all. Isn't this supposed to be the whole purpose of this product, to measure the internal temperatures of a refrigerator and freezer?
I don't know if our new refrigerator/freezer came with some sort of doors that the signal could not penetrate, but obviously this product would not work for us and I feel that the wireless signal they use is extremely poor. Amazon was great about letting me return this device, but now my wife and I cannot find any other wireless device to replace it with. There are a couple of others on the market, but they receive rather poor ratings as well and we are afraid to take a chance on them. I really, REALLY wanted to like the Chaney 00985 Wireless Refrigerator Freezer Thermometer. It looks awesome and the features of this product are exactly what we have been looking for. However, this device is obviously made of extremely poor quality, and I recommend that anyone who decides to purchase this product should keep the packaging and receipt handy, as it is likely you will end up needing to return it. I would gladly pay three times as much for this product if it would work reliably. In the meantime, if anyone knows of a product like this that is proven to work well, please let me know. Thank you.
Honest reviews on Chaney Instrument 00985 Wireless Refrigerator Freezer Thermometer
Given the mixed reviews of this product, I was pretty hesitant to order it. However, there weren't a lot of alternatives so I thought I'd go ahead and try it. I'm happy to say that it works just fine and I'm actually quite happy with it.------
SET-UP
------
The set-up was easy. I put the AA-Lithium batteries in the sensors first, and then the AAA-Lithium batteries into the base and within 1 minute it had registered both sensors and started working.
--------
ACCURACY
--------
This was my biggest concern given some of the other comments. However, with both sensors side by side on a table, they both read within 1 degree of each other, and both matched my external room thermometer. Good enough for me!
Then I placed them in my fridge and freezer. They took about 15 minutes to acclamatize and then started reading exactly the same as the readouts built in to the fridge.
--------
RANGE
--------
This was the key point for me. I needed something that was going to have range, as I don't want to have the main base attached to the outside of the door.
With the base attached to the door, no problem they worked fine.
With the base 20ft away and in the next room also worked great.
When I moved one of the sensors out of the freezer and into a room down the hall (about 35ft away) it stopped registering that one, but still read the other in the fridge (20ft away) I suspect the multiple walls were blocking the signal.
The one negative I would say about this, is that unlike the Orgagon Scientific thermometers I've used, this base unit provides no indication that it has lost contact with the sensor. I'd suggest that if it doesn't get an update within 2 minutes, it should show that on the screen somehow. Instead, this unit just keeps showing the last known temp -not very helpful.
Also, once it has lost it's connection, it seems that you have to remove the batteries or hit the paperclip sized reset button on the main base to re-initiate the connection.
-------
ALARMS
-------
Dead simple to set and exactly what I needed.
----------
BATTERIES
----------
I saw somebody else complained in a review that you have to use expensive lithium batteries in the sensors. That's a little silly isn't it? It's hardly the manufacturers fault that alkaline batteries would freeze in the freezer and not function.
My only complaint (and admitedly it's also a bit dumb) is that Amazon shipped the batteries in a separate box and 2 days later than the actual thermometers, so I had it sitting here for two days while I wanted to try it. See, told you it was dumb.
-----------------------
In closing, I think this is a good product. It seems well constructed. The mounting options of suction cups or spring clips on the sensors and wall hanging or magnets on the base are appreciated.
The only things that would make this a 5 star in my opinion are:
indicate when you've lost a signal
make the base available in silver and/or black
sell as a bundle with your first set of lithium batteries included.
I'm now going to take it out to my RV where I really need it. I will edit this if I have any future problems.
I'd buy it again...
Jay.
Find helpful customer reviews and review ratings for Chaney Instrument 00985 Wireless Refrigerator Freezer Thermometer
I am a wine writer and also a low carb writer. For both of the websites I run I get bombarded with questions from readers who want to know how to keep their wines and foods fresh for as long as possible. We are all trying to save money in these times, and keeping your food and drink fresh until you finish eating it is certainly an obvious way to help out. In almost every case, my guidance to the people is to test the temperature in their fridge and freezer. Many people are shocked to realize that their fridges are FAR too warm, and that is causing their food to spoil and their wine to sour.The Chaney Refrigerator / Freezer Thermometer is a brilliant way to keep an eye on how your food is doing. Here is how it works. You get one thermometer which you put into the back of your refrigerator. A second thermometer goes into the back of your freezer. Both of these send signals *wirelessly* to a display unit. The display unit is magnetic and can stick easily to the front of your refrigerator.
You can walk by your fridge and see at a glance exactly what temperature your fridge and freezer are currently at. The system also displays the highest and lowest temperature each area has reached since you last reset the values. So if you set your fridge normally to 34F and you see that it has been swinging between 20F and 50F, it's time to call a repair person! That would definitely cause serious damage to your food.
In addition, you can set alarm values, both high and low, for both sensors. So you can set the freezer to start beeping an alarm if it drops below -50F, or if it goes up above 0F. Of course the chance of your freezer suddenly going insane and becoming "way too cold" is probably slim but I know a number of people who had electrical problems with their fridges and who lost cooling ability without realizing it at first. Having a beeping alarm go off before your freezer's contents all thaw is a very good thing!
The wireless unit says that it can transmit a fair distance, but this of course would depend on all sorts of things if there are concrete walls between the source and destination, if there are other interfering signals around, and so on. For me, I know it works with the display on the outside of the fridge it is monitoring. So I can say with great certainty that that works very well.
I know for sure the alarm works wonderfully only a few weeks after buying the unit, we had a thunderstorm take out the power. It was only a short while later when the fridge half of our unit began beeping.
Is there a downside to this? Well, when we first got the set, the display LEDs simply would not light up well. We tried at least 8 different sets of batteries in it to ensure it wasn't a bad set of batteries. Some of the number pieces would light up, while others would stay completely unlit. We called up Chaney and they were extremely prompt and helpful. Only a few days later we had a fully functional display unit in our hands, and it worked beautifully. Electronic devices will never be 100% foolproof so I don't ding them much for having that glitch, and offer praise for them resolving it so readily.
All in all, I love this device. I can glance at my fridge every time I use it and know exactly what its temperature is and what the recent ranges of temperature have been. I can optimize the fridge and freezer to have the optimal temperatures to keep my food and wine fresh for as long as possible. That means milk lasts longer, salad fixings last longer, everything lasts longer. That stretches my food dollar as well as it can be stretched, and easily pays for the price of the thermometer within a month or two.
Highly recommended. I'm even looking into getting another one for my wine fridges. The only question then would be if the wireless transmitters interfere with each other!
Tuesday, January 21, 2014
Cheap Farberware P04-303 thermostat for coffemaker urn.
Save $50 by replacing your thermostat when your percolator stops making strong coffee. There is 1 nut to remove on the bottom of the percolator and 3 plugs to remove and put on the new thermostat (for the model I have). Waalaa now you will have that strong, hot coffee you loved.
Review. The replacement thermostat is an Elmwood thermostat from Honeywell Corporation. I installed it and fired up the 4 to 8 cup Farberware percolator and it worked just fine.
Click Here For Most Helpful Customer Reviews >>
Background. I own the Farberware coffee percolator 4 to 8 cup size. I purchased it in about 2003 and it operated about 4 years before it failed – daily use. The failure was typical in that the perc cycle got shorter and shorter until the coffee was only lukewarm and weak. I went out purchased another Farberware percolator in 2008 and it still operates. Having time I purchased a new thermostat for the first percolator that failed. When I pulled out the old thermostat it was identified as a TOD thermostat which is "Thermo Disc Company" a subsidiary of Emerson Corporation. I looked up the specs on this thermostat was surprised it had fairly good agency ratings including UL which approved it for 100,000 cycles. Clearly this thermostat is not living up the to the UL rating. Application notes to the TOD thermostat states, "These controls contain exposed electrical components and are not intended to withstand exposure to water or other environmental contaminants which can compromise insulating components. Such exposure may result in insulation breakdown and accompanying localized electrical heating." Perhaps water is a factor when cleaning the percolator. I intend to write to the UL rating agency and let them know their rating for this product doesn't seem right. Either production quality for the TOD thermostat has declined or it was used in the wrong application for these percolators.Review. The replacement thermostat is an Elmwood thermostat from Honeywell Corporation. I installed it and fired up the 4 to 8 cup Farberware percolator and it worked just fine.
Best Deals on Farberware P04-303 thermostat for coffemaker urn.
We purchaed a Farberware perculator and after a few months, noticed the coffee wasn't that hot anymore. We really didn't think that the thermostat was bad, afterall its "Farberware". I had a Farberware perculator years ago, and nothing was ever wrong with it....but then again, perhaps it was made in the USA at that time. We found the new thermostat on Amazon from a supplier "Goodmans". Since then, we had to purchase another thermostat, because the replacement didn't work anymore either!! We gave up, contacted Farberware...they sent a new perculator..but guess what happened?........you guessed it the thermostat went bad. We since then, purchased a "Westinghouse" perculator, and after a few weeks....guess what again?.......YEP...the termostat went bad. Contacted Westinghouse's supplier/manufacturer (can't think of the name) they sent us a new pot. Now, we have hot perculator coffee again..but for how long, we don't know. Probably the same thermostat is in the Westinghouse pot too...but we're not going to dismantle it to find out. All I know is, these people who are putting crappy thermostats in perculators, should re-evaluate their product. BEWARE.Honest reviews on Farberware P04-303 thermostat for coffemaker urn.
Item was as shown and easy to decide it was the right part because of the great photos. Part was installed and works well.Monday, January 13, 2014
Buy Honeywell Sure-Set Ceramic Heater with Oscillation, HZ-338
Customer Ratings: 
List Price: $59.99
Sale Price: $44.95
Today's Bonus: 25% Off

Got one of these today. Thot the other guys that had this problem were just unlucky, and decided to trust the Honeywell name. Boy, was I wrong. SureSet, my foot. The thermostat in this device does indeed seem to be measuring the temperature of the unit itself, although not the actual element, maybe the heated plastic body. I do not recommend that anyone buys this heater if they want to use the automatic mode. It functions well in the high and low constant heating mode. I have a lasko 5365 heater as well, that works well in all modes.
Update: Lasko 5365 is displaying same odd thermostat behaviour, I am beginning to think this behaviour is a product of the environment where the heater is used, and not just poor manufacturer design.
Update 2: Confirmed that 5365 thermostat works fine if heater placed in middle of open space to be heated as opposed to against a wall. HZ-338 thermostat performance doesn't seem to improve when in open area.
At night, I turn it on to the low setting, set the temperature, set the timer, and it does the rest. It isn't as loud as my older heater that it is replacing, and I don't have to worry about remembering to turn it off in the morning.
I have since purchased a second one for my bedroom.
I have not had any of the problems the other reviewer mentioned.
List Price: $59.99
Sale Price: $44.95
Today's Bonus: 25% Off
Got one of these today. Thot the other guys that had this problem were just unlucky, and decided to trust the Honeywell name. Boy, was I wrong. SureSet, my foot. The thermostat in this device does indeed seem to be measuring the temperature of the unit itself, although not the actual element, maybe the heated plastic body. I do not recommend that anyone buys this heater if they want to use the automatic mode. It functions well in the high and low constant heating mode. I have a lasko 5365 heater as well, that works well in all modes.
Update: Lasko 5365 is displaying same odd thermostat behaviour, I am beginning to think this behaviour is a product of the environment where the heater is used, and not just poor manufacturer design.
Update 2: Confirmed that 5365 thermostat works fine if heater placed in middle of open space to be heated as opposed to against a wall. HZ-338 thermostat performance doesn't seem to improve when in open area.
Click Here For Most Helpful Customer Reviews >>
I purchased a white version of this heater elsewhere about a month ago. I love it. It is in my daughter's bedroom, which tends to be colder than the rest of the house.At night, I turn it on to the low setting, set the temperature, set the timer, and it does the rest. It isn't as loud as my older heater that it is replacing, and I don't have to worry about remembering to turn it off in the morning.
I have since purchased a second one for my bedroom.
I have not had any of the problems the other reviewer mentioned.
Best Deals on Honeywell Sure-Set Ceramic Heater with Oscillation, HZ-338
The thermometer of this heater is completely messed up. It does not measure the room temperature, but the temperature of the air that has just been heated up. In other words, if your room temperature is 60 degrees and you program it to heat up the room to 70 degrees it will do so (according to the thermometer reading) in less 2 minutes and stop. If you do not use this functionality, but instead let the heater run for some time (5-10 minutes) the thermometer will want to make you believe that the room temperature has gone up to 90 degrees. The thermometer is probably in the wrong location. Did Honeywell do any kind of testing before putting this model on the market ?!Honest reviews on Honeywell Sure-Set Ceramic Heater with Oscillation, HZ-338
Ditto the other's observations... The thermostat seems to register the temperature of the unit itself rather than the room... I had the thing in a 63 degree room, had it set to 85 degrees. It would register 90 after 30 seconds of running, turn off, slowly ramp back down to 84 degrees over a 2 minute time period, and then repeat. The temperature of the room never got above 64 degrees....Find helpful customer reviews and review ratings for Honeywell Sure-Set Ceramic Heater with Oscillation, HZ-338
My daughter has been using this unit in her bedroom everyday this winter. It does a good job of heating her room. HOWEVER I've noticed that the plastic case has actually started to warp and MELT, the seam where it's put together is starting to open, you can see the wiring inside.
Subscribe to:
Posts (Atom)